Control of Size Pick-up

Control of size pickup

For control on variation of size pick up , the two steps required are:

a. determination of average size pick up on the beam
b. Suitable adjustment in sizing conditions

a. Determination of average size pick-up

Example: The weight of sized yarn on a beam was found to be 82.5 lbs. The beam contains 1050 yards of warp, whose count before sizing was 50s cotton.If the number of ends in the warp is 3000, calculate the following:
a. The weight of size on the yarn
b. The % of size put on the yarn
c. The count of sized yarn

a. Weight of size on warp= weight of sized warp- weight of same length of unsized warp

Now weight of unsized warp= (No of ends x length of warp in yds)/(count of unsized yarn x 840)= (3000x1050)/(50x840) = 75 lbs

Therefore weight of size on warp = 82.5 -75 = 7.5 lbs

b. Percentage of size on warp = (wt of size x 100)/ wt of unsized warp

= (7.5x1000)/75 = 10%

c. Count of sized yarn = (No of ends of the warp x length of warp in yds)/(wt of lbs of warp x 840) = (3000x1050)/(82.5x840)= 45.5s cotton

b. Control on sizing condition

1. Viscosity of size paste in size box: Any variation in the concentration or temperature alters the viscosity of the paste which in turn affects both the level of size pick up and extent of penetration. Initially as the viscosity increases, the size pick-up also increases. But as the viscosity increases beyond a point, the size pick up is reduced.

2. Sqeezing pressure and condition of squeezing nip: The squeesing pressure determines the extent of penetration of the size paste between the fibres of the yarn and also of the removal of excess size paste and hence the level of the size pick up.

3. Speed of the sizing machine: Other sizing conditions remaining unchanged, the size pick up increases with increasing sizing speed and vice versa. This is because the time available to squeeze the surplus size from the yarn is less at high speeds.

4. Depth of immersion roller in size paste: the depth of immersion roller in the paste determines the duration for which the yarn remains immersed in the paste. this duration in turn influences both the level of size pick up and the extent of size penetration.

5. Level of size paste in the size box: Variation in the level of size paste is an important source of size pick-up variations both within and between beams.

6. Density of ends: When the density of ends is high, difficulties are encountered in obtaining adequate and uniform size penetration. Therefore size pick up may vary at these fabrics.

Choice of Size Receipe

Choice of Size Receipe

The suitability of size receipe for the type of yarn should take into account, fabric construction, and end use as follows:

1. Cotton Yarn- Starch Based
Polyester etc.- Polyvinyl Alcohol (PVA) based

2. Fine and Superfine cotton- thin boiling Starches
Coarse Count- ordinary starch

3. Heavy Fabrics- Modified starches
Light and Medium- Ordinary starches

4. conventional sizing Machines- Low viscosity starch
High speed sizing machines- High viscosity starches

5. Unlbleached calendered sort of fabrics- More weighting agents, antiseptic softners etc. are used.
Bleached sorts- ordinary starches

6. Finer Counts and Heavier Constructions- More size pickups
Coarse counts- Less size pickups

7. Plied yarns- low size pick up or nil even

Ingredients for water Based Sizes

1. Adhesives- Potato starch, starch from cereals ( corn, wheat, rice etc0, carboxy methyl cellulose (CMC), Polyviny alcohol (PVA), Polyviny Chloride (PVC)

2. Lubricants- Mineral Waxes, vegetable waxes, animal fats, mineral oils, vegetable oils

3. Additives- Salicylic Acid, Zinc Chloride, Chloride emulsifiers.

Suggested Size Receipe

Ordinary starch=100
Gum= 2
Mutton tallow= 7.5

Preparation of Size Receipe

1. Ingredients

Water= 18.5"
Modified Starch = 50 kg
CMC= 5 kg
PVA= 10 kg
Gum = 1.5 kg
Softner= 1.2 kg
Antistat= 0.8 kg

Mixing: Took 17" water. Added Starch, Gum, CMC and PVA slowly and one by one as the slurry is stirred. Softner and antistat added in storage kettle.

Cooking

1. cold stirring at 50 rpm = 12 min
2. Transfer into pressure cooker through sieve=== 45 deg C
3. Stirrer rpm in cooker== 55
4. Close lid, open steam inlet, open air vent
5. Close air vent valve when steam is seen escaping through it, temperature = 96 deg C, Pressure = 10 PSI
6. time between point 3 and 4 == 15 min
7. Cooking starts, steam continued till temperature = 130 deg c, Pressure = 40 PSI
8. Time for getting 130 deg C after closing air vent valve = 25 min
9. Stem in-let closed
10. 10 minutes after closing steam, Temp= 124 deg C, Pressure = 32 PSI
11. Total cooking time after getting 130 deg C= 35 min
12. Flow time of paste taken through sample valve= 24 seconds
13. Transferred to storage beck
14. Final volume = 18.5 "
15. Stirrer RPM in storage beck = 20
16. Temperature after 10 min. of transfer = 100 deg C
17. Refrectometer reading= 16

Lab Data

1. Size add on = 18 %
2. Increase in strength % = 5.2
3. Elongation at break % os sized yarn = 6.8%

Process Control in Sizing-1

Sizing

The process consists of laying warp yarn parallel and sizing the yarn with a mixture to strengthen it to withstand the rigours of weaving.

Warp yarn is withdrawn in sheet from from warp beams which are placed at the back of the sizing machine. The yarn is then passed through sow box. Size solution is applied by immersion. After removing surplus solution that occurs at this state, the yarn is dried and arranged on a loom beam.

The objective of sizing is RESISTANCE to ABRASION

This objective is achieved by applying on the yarn a unifrom and smooth protective film of suitable sizing material.

We also want that in the sized yarn there should be

- Some increase in tensile strength in the yarn
- Minimum loss of extensibility in yarn ( about 4.4-4.6% elongation at break is required for cotton)
-Required moisture content ( 8-10% of cotton)
- Good quality of sized beam (neither too soft nor too firm + free from yarn defects)
- Good productivity and efficiency
- Reduced Cost

Process Control in Sizing

The process control programme in sizing should, therefore, comprise of the following aspects:

1. Selecting the correct size receipe and size pick -up level
2. Ensuring correct preparatio of size paste
3. Control of
- size pick up
- stretch
-moisture content
-quality of beam
-machine speed
-machine efficiency
-a method to calculate the expected level of productivity

Cost of Warping

Warping process is required exclusively for preparing warp yarn for weaving. Hence warping cost should be calculated for warp yarn.

Unit costs in this section can be developed on weight basis or on length basis.

Weight Basis

Warping cost per piece length of fabric= weight of warp yarn per length x cost per unit weight.

If unit costs are developed on length basis, they are expressed with reference to specific number of ends (generally 400-500 ends). It follows , therefore, that about four to eight beams ( some time even more) would be required to made one beam for weaving.

In other words, unit cost in terms of length will have to be multiplied by the number of warp beams required per weaving beam. Then warping cost per piece length of a fabric can be calculated as shown:

warping cost per piece length of fabric = cost per meter x tape length x no of warp beams per weaving beam.

If the warp beam is partly colored and partly greige, warping cost should be calculated for greige warp yarn and coloured warp yarn. Generally coloured yarn is processed on slow speed warping frame. Hence cost of color warping usually works out higher as compared to the cost of greige warping.